Bissell model 3990 manual

See also: User Manual. Table of Contents. Pet Hair Eraser. Previous Page. Next Page. Bissell canister bagless vacuum cleaner user guide 21 pages. Bissell bagless vacuum user's guide series 21 pages.

Bissell bare floor vacuum cleaner user's guide , 10 pages. If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a 13 amp socket. Attach handle to vacuum Locate the handle and cord wrap. Remove the screw packet taped to the handle.

Stand the vacuum upright and from the Connect the curved hose wand to the hose. Page 7: Handle Positions perations Handle positions Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions. Upright — For storage and above floor cleaning with tools.

Normal Cleaning — Page 8: Transporting Cleaner perations Transporting cleaner To move your cleaner from room to room, put the handle in the upright position, tilt the cleaner back on its rear wheels and push forward. The cleaner can also be moved by using the carry handle. Clean filter indicator The clean filter Indicator tells you when the air flow in your vacuum is reduced due to dirty filters or a Page 9: Special On-Board Tools Always place vacuum cleaner on the floor with handle in upright position when using tools.

Never place your fingers under the cleaner when it is running. Loop power cord around cord wraps on rear of vacuum cleaner. Be sure to first return the quick release cord wraps back to their original position before wrapping the cord. Grasp handle and pull the dirt container straight out to remove from the vacuum. Page 12 Unplug the vacuum from electrical outlet.

Place handle in low position and turn vacuum cleaner over so bottom side is facing up. Remove the screws marked 1 and 2, Release the latches marked 3 and 4. Lift off the brush cover. Generic belts may not meet the exact specifications required to keep your vacuum operating at its peak performance. Do not run appliance over cord. Keep cord away from heated surfaces. To unplug, grasp the plug, not the cord.

Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow. To reduce the risk of electric shock, this appliance has a polarized plug one blade is wider than the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

Locate the handle and cord wrap. Remove the screw packet taped to the cord wrap. Stand the vacuum upright and from the rear of the unit, slide the base of the handle firmly into the grooves at the top of the vacuum body. Ensure that the handle and cord wrap are firmly fit to the vacuum body.

If there are any gaps, continue to push firmly until the handle and cord wrap are flush. Insert 2 of the screws provided 3 total into the existing holes, attaching the cord. Tighten securely with a screwdriver. Attach the hose and cord clip by snapping it into the handle of the unit. Secure it by inserting the screw provided. Attach the lower hose clip by snapping it into place and twisting to the right. Connect the curved hose wand to the hose. Grasping the curved hose wand, slide the end of the curved hose wand onto the hose wand base.

Snap the hose into the hose clip. NOTE: The vacuum will not operate effectively unless the curved hose wand is firmly attached. Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures. Hose Clip. Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children. Slide the extension wand and crevice tool together into the storage clip.

Attach the TurboBrush by snapping it onto the top cap of the upper tank. The power switch is located just below the handle on the front of the vacuum. Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning positions.

Upright — For storage and above floor cleaning with tools. Normal Cleaning — Press handle release pedal once. Position used. Low Cleaning — With the vacuum in normal cleaning position, press handle release pedal again.

Use for reaching under low furniture such as tables, chairs or beds. Before using your vacuum, make sure that the dirt container is in the locked position and that all filters pre-motor and HEPA post-motor are in place. Do not operate your vacuum without these filters. For above floor cleaning, the floor brush will continue to rotate but is raised above floor.